Occasionally, you may require to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be completed in just a few actions.
- Begin by ensuring your red dot sight is activated.
- Find the small reinitialize button on the side of the unit.
- Use a small object to activate the reset button for approximately three moments.
- Release the reset button and your Holosun EPS Carry Red Dot sight will reboot.
- Your red dot sight should now be returned to its factory settings.
Restore Your Holosun EPS Carry Red Dot toward Defaults
In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to its factory configuration is a breeze. First, determine the tiny button on the bottom of your optic. Then, keep pressed it for around twelve seconds until you see the red dot blink. Your Holosun EPS Carry is now reset to its factory settings, ready for accurate shooting.
Bring Your Holosun EPS Carry Back to : Functionality
Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unexpected activation during the process.
To perform a factory reset on your Holosun EPS Carry, follow these easy steps:
- Hold down the power button for approximately 10 seconds.
- The display will flash, indicating that the reset is in progress.
- Release the power button once the reset is complete.
Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and confirm your sight's functionality. If you encounter any further difficulties, don't hesitate to contactsupport team.
Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide
Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.
- First, Activate your Holosun EPS Carry by pressing the power button.
- Next, press and hold both the mode button and the up/down adjustment button simultaneously.
- As you continue holding these buttons, tap the power button once.
- A message will show a confirmation prompt indicating that the reset process is initiated.
- Permit the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.
After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.
Erase All Settings on Your Holosun EPS Carry
To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can here usually be done by Turning a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.
Reset your Holosun EPS Carry through a Factory Original Settings
If your Holosun EPS Carry is acting up, a factory reset might be the fix. This will restore your sight to its factory settings, clearing any personalized configurations you've made. To perform this reset, observe these straightforward steps:
- First, identify the reset switch on your EPS Carry.
- Secondly, use a thin object, like a pen tip, to depress the reset lever.
- During maintain the reset switch pressed, power on your EPS Carry.
- The sight will flash a message confirming that the reset is successful.
Once the reset is successful, your EPS Carry will be set to its factory settings.